Oracal 638 On the computer Cut setting – Vinyl Matte Blade- 1 Speed- 5 Force- 10 Passes- 1 Oracal 651 Vinyl On the computer Cut setting – Vinyl Glossy Blade- 1 Speed- 5 Force- 11 Passes- 1 Pastel Vinyl– On the computer Cut setting – Vinyl Matte Blade- 1 Speed- 5 Force- 8 Passes- 1 Rose Gold Vinyl-On the computer Cut setting – Vinyl Metallic Blade- 1 Speed- 5 Force- 14 Passes- 1 Paint mask Vinyl On the computer Cut setting – Vinyl Frosted Blade- 1 Speed- 5 Force- 7 Passes – 1 Glass Etch Vinyl- On the computer Cut setting – Vinyl matte Blade- 1 Speed- 5 Force- 10 Passes- 1įluorescent Vinyl On the computer Cut setting – Vinyl Glossy Blade- 1 Speed- 5 Force- 10 Passes- 1īlackboard Vinyl On the computer Cut setting – Vinyl Matte Blade- 1 Speed- 4 Force- 3 1 Passes- 1 Stained Glass Vinyl On the computer Cut setting – Vinyl Glossy Blade- 1 Speed- 5 Force- 8 Passes- 1 Gemstone Glitter Vinyl On the computer Cut setting – Vinyl Glitter Blade- 2 Speed- 5 Force- 10 Passes- 1 GM Premium Glitter Vinyl On the computer Cut setting – Vinyl Glitter Blade- 2 Speed- 5 Force- 12 Passes- 1 Matt Vinyl On the computer Cut setting – Vinyl matte Blade- 1 Speed- 5 Force- 8 Passes- 1 Gloss Vinyl On the computer Cut setting – Vinyl Glossy Blade- 1 Speed- 5 Force- 8 Passes- 1 Prime Vinyl On the computer Cut setting – Vinyl Glossy Blade- 1 Speed- 5 Force- 10 Passes- 1 Holographic Vinyl On the computer Cut setting – Vinyl Glitter Blade- 2 Speed- 5 Force- 10 Passes- 1 Metallic Vinyl– On the computer Cut setting – Vinyl Metallic Blade- 2 Speed- 5 Force- 10 Passes- 1 Pattern Glitter Vinyl On the computer Cut setting – Vinyl Glitter Blade- 2 Speed- 5 Force- 12 Passes- 1 Pattern Vinyl- On the computer Cut setting – Vinyl Matte Blade- 1 Speed- 5 Force- 8 Passes- 1 SELF ADHESIVE VINYL Click on the green Product name to be taken to it's page. If you are having cutting issues, please check your blade, unscrew the cap and photograph the tip shown as below so you can zoom in to check for damage. The clear side always goes to the mat and the vinyl side faces up. We always suggest peeling the corner of the sheet of vinyl to check which side has the clear carrier (or paper sheet if self adhesive) and which corner side has the vinyl. Speed is set as below, to reduce ripping and tearing and ideally should not be altered either. Whilst force can be altered, we have the settings recommended below to extend your blade's lifespan and excessive pressure can dull or chip your blade. Please be aware Silhouette can alter pre set settings when doing an update, so if a previous setting stops working and you have checked your blade for damage, then do repeat test cuts increasing Force and if needed blade depth until you have found the new setting you need. Please note that the blue/green dot in your blade holder should be visible and the clamp fully pressed in and clicked closed. Settings below are made with the Auto blade and may vary if the blade is well used, chipped or if a new or different blade, eg ratchet is used so please test cut if in doubt before wasting any product. If the test cut works well and the design you are using struggles it may be worth adding an offset line to widen it. When using these cut settings it is worth bearing in mind the type of vinyl you are using, as some is more suited to fine, intricate detail please see product descriptions for each vinyl's capability. Please see how to test cut at the bottom of the page, full instructions provided below. It is okay to change the force a few times, as all machines vary slightly due to many variables effecting calibration. If it doesn't cut enough please increase the force and cut again, repeating the process if needed. If it cuts too deep please reduce the force. ![]() The software offers you a test feature or you can use a small hexagon about the size of a 5 pence piece. Please ensure you use a test cut on any new vinyl before using it for the first time, so you may check that the settings below work with your machine. The settings below are for the Silhouette Cameo 4. We would love to see what you make! Have you found our You Tube channel yet? There is lots of videos showing tutorials available on there, as well as exclusive demos, inspiration and more! Join us for more inspiration on Facebook , Instagramor Tiktok or send us an email to we would love to hear from you! Please Test cut as described in the following information when using a new product.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |